 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ALUMINUM ELECTROLYTIC CAPACITORS WS Chip Type, High CV High Temperature (260C) Reflow series Corresponding with 260C peak reflow soldering Recomended reflow condition : 260C peak 5 sec. 230C over 60 sec. 2 times (8 x 6.2, 10 x 10 : 1 time) Chip type higher capacitance in large case size. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). WS High Temperature www..com Reflow UR Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current Tangent of loss angle (tan ) Performance Characteristics - 40 to +85C 6.3 to 50V 22 to 1500F 20% at 120Hz, 20C After 1 minute's application of rated voltage, leakage current is not more than 0.03CV (A) . Measurement frequency : 120Hz, Temperature : 20C Rated voltage (V) tan (MAX.) 6.3 0.28 10 0.24 6.3 5 10 16 0.20 10 4 8 25 0.16 16 3 6 35 0.14 25 2 4 35 2 3 50 0.12 Measurement frequency: 120Hz Stability at Low Temperature Rated voltage (V) Z- 25C / Z+20C Impedance ratio ZT / Z20 (MAX.) Z- 40C / Z+20C 50 2 3 Endurance The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours at 85C. Capacitance change tan Leakage current Within 20% of initial value 200% or less of initial specified value Less than or equal to the initial specified value Shelf Life After storing the capacitors under no load at 85C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250C for 30 seconds. After removing from the hot plate, the capacitors meet the characteristic requirements listed at right when they are restored to 20C. Black print on the case top. Capacitance change tan Leakage current Resistance to soldering heat Marking Within 10% of initial value Less than or equal to the initial specified value Less than or equal to the initial specified value Chip Type (6.3, 8 x 6.2) Voltage (A:10V) C0.2 0.5MAX. Plastic platform 0.3MAX. Positive Type numbering system (Example : 10V 100F) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 UWS 1 A 1 0 1 M C L 1G S Package code A0.2 Configuration Capacitance tolerance (20%) Rated Capacitance (100F) A0.2 Rated voltage (10V) Series name Type Series N2 100A WS D0.5 1 Trade mark B0.2 Lot No. Capacitance L 0.3 H 1 Size 8 x 6.2 only E Negative (mm) (8 x 10, 10 x 10) Positive Voltage (V:35V) Series C0.2 0.5MAX. Plastic platform 0.3MAX. DxL 6.3 x 5.8 2.4 6.6 6.6 2.2 5.8 0.5 to 0.8 6.3 x 7.7 2.4 6.6 6.6 2.2 7.7 0.5 to 0.8 8 x 6.2 3.3 8.3 8.3 2.3 6.2 0.5 to 0.8 8 x 10 2.9 8.3 8.3 3.1 10 0.8 to 1.1 10 x 10 3.2 10.3 10.3 4.5 10 0.8 to 1.1 N2 100V WS D0.5 B0.2 Lot No. Capacitance L0.5 H Negative Voltage V Code 6.3 j 10 A 16 C 25 E 35 V 50 H Dimension table in next page. A0.2 Trade mark E A0.2 A B C E L H CAT.8100X ALUMINUM ELECTROLYTIC CAPACITORS WS Cap. (F) series Dimensions V Code 6.3 0J 10 1A 16 1C 25 1E 6.3 x 5.8 6.3 x 5.8 065 145 192 250 305 393 8 x 6.2 8 x 10 8 x 10 10 x 10 10 x 10 35 1V 6.3 x 5.8 055 105 175 214 265 324 8 x 6.2 8 x 10 10 x 10 10 x 10 10 x 10 50 1H 045 095 140 195 238 289 22 33 47 220 330 470 101 151 221 331 471 681 102 152 8 x 6.2 8 x 6.2 8 x 10 8 x 10 10 x 10 10 x 10 160 190 265 318 400 489 6.3 x 5.8 6.3 x 5.8 8 x 6.2 8 x 10 8 x 10 10 x 10 10 x 10 070 085 175 240 290 374 454 8 x 6.2 6.3 x 7.7 8 x 10 8 x 10 10 x 10 10 x 10 125 151 215 270 330 396 www..com 100 150 220 330 470 680 1000 1500 8 x 6.2 8 x 10 10 x 10 10 x 10 10 x 10 Case size D x L (mm) Rated ripple Rated Ripple (mArms) at 85C 120Hz Frequency coefficient of rated ripple current Cap.(F) Frequency 00 Less than 47V 100 to 1500 50 Hz 0.80 0.85 120 Hz 1.00 1.00 300 Hz 1.15 1.08 1 kHz 1.40 1.20 10 kHz or more 1.67 1.30 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100X |
Price & Availability of UWS0JXXXXXXXXX
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |